Upgrade to the __tier_name__

You’re attempting to view exclusive content only for members in the __tier_name__.

Upgrade to __tier_name__ Go back to shopping
Upgrade to the __tier_name__

You’re attempting to view exclusive content only for members in the __tier_name__.

Current Plan
Upgrade to __tier_name__
or compare all plans on landing page
Your Cart
  • Your cart is currently empty.

Picks For You

Subtotal

$0.00

Checkout Continue shopping
Spend More, Get More: FREE Gift Card on $100+ Orders
Over 10,000 Reviews
Menu

If you have a dead zone or a lack of thrust with your NK180, you may be able to recalibrate your controller. 

  • If you have a serial number below serial number 20210320001, your controller can't be recalibrated. Please file a warranty claim here for a replacement unit. 
  • If your serial number is above serial number 20210320001, please see the steps below to recalibrate.

1. Connect the NK180 to a battery source and plugin speed controller.

2. DO NOT attach the magnet emergency stop key to the remote. 

3. The remote controller LED display will show 3 dashes in each category (Battery voltage, throttle percentage, and power input display). Start by putting the throttle to 100%, press and hold the "MODE" button. After a second, 3 dashes should appear on the screen.

Step_3.png

4. Move the throttle into the complete forward position (full throttle).

5. Firmly press and hold the “MODE” button down until the screen display goes blank and shows. ONLY 3 dashed lines on the top of the screen display

step_5_A.png  --->Step_5_B.png

6. Once the 3 dashes appear on the screen, release the hold on the “MODE” button.

step_6.png 

7. Change the position of the throttle handle. Position the handle all the way down.

Step_7.png

8. Firmly press the “MODE” button once on the LED display and release. Once the “MODE” button is released, a set of 2 dashes on the screen will appear after one second.

Step_8_A.png ---->Step_8_B.png

9. Move the throttle to the center position.

 Step_9.png

10. Press the “MODE” button one time and release. Once the “MODE” button is released, 3      dashes will appear on the bottom end of the LED screen.

Step_10_A.png----->Step_10_B.png

11. Change the position of the throttle to the most forward position one more time. 

Step_11.png

12. Click the “MODE” button once and release. Three dash sets should disappear, and the LED screens will have 3 sets of the number 8.  

Step_12_A.png ---->Step_12_B.png

13. Leave the throttle in the forward position and click the “MODE” button one more time. Release the “MODE” button, and the screen will change its appearance to three sets of dashed lines. Leave the throttle in the forward position and click the “MODE” button one more time. Release the “MODE” button, and the screen will change its appearance to three sets of dashed lines.

Step_13_A.png --------> Step_13_B.png

14. The calibration will be complete, and the screen will go blank. The speed controller is now calibrated with throttle percentages from 0%-100%.

Step_14.png

If you have any questions about our NK180, please see our NK180 FAQ Page and videos on YouTube for installation instructions. Please see our Recommended Batteries for the NK180 for 24V battery options with the NK180 and use our Run-Time Calculator to estimate your battery life depending on the battery amperage size!

If you would like to see if your vessel is compatible with the NK180, please see our Compatibility Examples link. If you need additional information, give us a call (866) 721-0002 Monday to Friday: 8:30 am - 4:30 pm PST or reach out to us via email SUPPORT@NEWPORTVESSELS.COM.

    Back to Electric Outboards